The discussion is excerpted from our conversation. One of the subjects he covered was trying out different types of seafaring rigs for a newly built wooden sailboat which could easily apply to a self-built wooden Trimaran. The going with article will lead us through the subject Making and testing sailing chicago rigs.
Also to keep things manageable, I would suggest using only the mainsail, for now, it's best to wait until you have gained a certain amount of experience by using the sails individually at first. You will have plenty of opportunities to use both at a later time. Assuming that the main is up, next, you will need to turn the tiller towards your intended direction of travel until the sail finds the wind.
By the way, a tiller is the steering control mechanism on smaller nautical boats. However take note, the tiller steers in the opposite direction you will want to go. For instance, if you push the tiller towards the starboard [right side], the boat will steer to the left or the port side.
When it comes to experimentation Polycarp is an underrated material. If you see a picture on the Duckworks website of my boat called "Caprice, " you'll notice it's a 25' Cat Ketch. I built it several years ago. You can visit the site and see a picture of it on the "About" page. The Caprice has got tanbark sails now, which were made by our sail maker.
Just keep in mind that seafaring downwind is much faster and easier than tacking! It's a good reminder to be aware of the time and allow plenty of time to get back to your original destination. Your next task is to trim the mainsail to the wind by using the boom block. The boom block is a sailing term that is a set of pulleys that are attached to the end of the boom and allows you to position the boom in various angles.
Inspect Your Stitching on Every Seam and lubricate your Mast Boom Slot: Thread holds your sails together. And after time, even triple-stitched panels, patches, and seams break down. Battens rub against pocket stitching, and sails flog and flap. Check the folded seam stitching along each sail edge. Next, move across each horizontal panel.
You can even tape pieces of tarp together at first. Then go back and sew them later if you want ... Or just leave them taped together. Another great thing about poly tarp is that you can try different things to create different types of sails. You can add shape to different sails by way of "darts." There is a great essay on the Duckworks website about cutting "darts" in sails to give them shape.
Next, you'll need to turn or come about. There are essentially two ways to accomplish this, by tacking or turning upwind is one way, or you can jibe or turn downwind which is faster than a tack turn. The reason being is that in a jibe turn you have the wind behind you pushing the sailboat through the turn, as opposed to a turning into the wind in a tack turn.
Also to keep things manageable, I would suggest using only the mainsail, for now, it's best to wait until you have gained a certain amount of experience by using the sails individually at first. You will have plenty of opportunities to use both at a later time. Assuming that the main is up, next, you will need to turn the tiller towards your intended direction of travel until the sail finds the wind.
By the way, a tiller is the steering control mechanism on smaller nautical boats. However take note, the tiller steers in the opposite direction you will want to go. For instance, if you push the tiller towards the starboard [right side], the boat will steer to the left or the port side.
When it comes to experimentation Polycarp is an underrated material. If you see a picture on the Duckworks website of my boat called "Caprice, " you'll notice it's a 25' Cat Ketch. I built it several years ago. You can visit the site and see a picture of it on the "About" page. The Caprice has got tanbark sails now, which were made by our sail maker.
Just keep in mind that seafaring downwind is much faster and easier than tacking! It's a good reminder to be aware of the time and allow plenty of time to get back to your original destination. Your next task is to trim the mainsail to the wind by using the boom block. The boom block is a sailing term that is a set of pulleys that are attached to the end of the boom and allows you to position the boom in various angles.
Inspect Your Stitching on Every Seam and lubricate your Mast Boom Slot: Thread holds your sails together. And after time, even triple-stitched panels, patches, and seams break down. Battens rub against pocket stitching, and sails flog and flap. Check the folded seam stitching along each sail edge. Next, move across each horizontal panel.
You can even tape pieces of tarp together at first. Then go back and sew them later if you want ... Or just leave them taped together. Another great thing about poly tarp is that you can try different things to create different types of sails. You can add shape to different sails by way of "darts." There is a great essay on the Duckworks website about cutting "darts" in sails to give them shape.
Next, you'll need to turn or come about. There are essentially two ways to accomplish this, by tacking or turning upwind is one way, or you can jibe or turn downwind which is faster than a tack turn. The reason being is that in a jibe turn you have the wind behind you pushing the sailboat through the turn, as opposed to a turning into the wind in a tack turn.
About the Author:
You can get a summary of the factors to consider when picking a sailing Chicago instructor and more information about an experienced instructor at http://www.saltydogchicago.com now.
No comments:
Post a Comment